BUY NOW, PAY LATER WITH AFTERPAY OR SEZZLE

5.7" x 15.5" Sublimatable Rectangle Hardboard Wall Decor with Ribbon

5.7" x 15.5" Sublimatable Rectangle Hardboard Wall Decor with Ribbon

Regular price
$10.00
Sale price
$10.00

UNISUB HARDBOARD WALL DECOR SUBLIMATION

Supplies needed:
- sublimatable hardboard
- sublimation transfer
- teflon or scratch paper
- heat tape
- soft paper towel (optional but recommended)
Heat press settings:
- temperature - 390 degrees F
- dwell time - 1:30
- pressure - medium

Note: The recommended settings above may need adjustments for best results.
Settings will vary depending on the heat press brand and model ink and paper
and atmospheric conditions.

2nd Note: Prepress the board faceside up alone for 10 to 20 seconds sandwiched
with smooth paper towel on both sides to help "steam out" any excess moisture.
Allow board to cool until you can handle safely.

3rd Note: The layers of soft paper towel during sublimation achieve two goals:
1. it helps to distribute the pressure evenly throughout the substrate; 2. it
helps to trap ink that is dispersed outside of the edges of the substrate if
there is an overprint area or full bleed in the artwork.

Layer the press from the bottom pad to the top heat platen as follows:
1. teflon sheet or scratch paper
2. 2-3 layers of soft paper towel (this helps distribute the pressure evenly)
3. hardboard substrate
4. transfer
5. teflon sheet or scratch paper

Steps:
1. Remove the protective plastic coating if any from the substrate
2. Place the hardboard onto the transfer.
3. Tape two ends of the hardboard to the transfer using the heat tape.
4. Place the transfer and hardboard in the press onto the paper towel
(transfer on top of the hardboard)
5. Place the teflon sheet or scratch paper over the transfer and metal.
6. Press the items using the settings listed above.
7. Remove items from the press immediately. Use heat resistant gloves if
necessary - the items will be very hot.
8. Tear the transfer in half opposite of the taped ends.
9. Attach ribbon to hang the item after cooling
UNISUB HARDBOARD WALL DECOR SUBLIMATION

Supplies needed:
- sublimatable hardboard
- sublimation transfer
- teflon or scratch paper
- heat tape
- soft paper towel (optional but recommended)
Heat press settings:
- temperature - 390 degrees F
- dwell time - 1:30
- pressure - medium

Note: The recommended settings above may need adjustments for best results.
Settings will vary depending on the heat press brand and model ink and paper
and atmospheric conditions.

2nd Note: Prepress the board faceside up alone for 10 to 20 seconds sandwiched
with smooth paper towel on both sides to help "steam out" any excess moisture.
Allow board to cool until you can handle safely.

3rd Note: The layers of soft paper towel during sublimation achieve two goals:
1. it helps to distribute the pressure evenly throughout the substrate; 2. it
helps to trap ink that is dispersed outside of the edges of the substrate if
there is an overprint area or full bleed in the artwork.

Layer the press from the bottom pad to the top heat platen as follows:
1. teflon sheet or scratch paper
2. 2-3 layers of soft paper towel (this helps distribute the pressure evenly)
3. hardboard substrate
4. transfer
5. teflon sheet or scratch paper

Steps:
1. Remove the protective plastic coating if any from the substrate
2. Place the hardboard onto the transfer.
3. Tape two ends of the hardboard to the transfer using the heat tape.
4. Place the transfer and hardboard in the press onto the paper towel
(transfer on top of the hardboard)
5. Place the teflon sheet or scratch paper over the transfer and metal.
6. Press the items using the settings listed above.
7. Remove items from the press immediately. Use heat resistant gloves if
necessary - the items will be very hot.
8. Tear the transfer in half opposite of the taped ends.
9. Attach ribbon to hang the item after cooling
Click to edit the product in Ali Orders.
Note: only show for shop owner